Sudesh S

Mathew L.

Vellore Institute of Technology (VIT) is a private university located in&nbsp;Tamil Nadu, India. Founded in 1984, as Vellore Engineering College, the institution offers 20 undergraduate, 34 postgraduate, four integrated and four research programs. It has campuses in Vellore, Amravati, Bhopal and Chennai.

VIT is one of the top ranked private universities in India according to NIRF, THE and QS Rankings.&nbsp;Govt. of India has recognized&nbsp;VIT, Vellore as an&nbsp;Institution of Eminence. This has allowed VIT to take independent quality initiatives and move up in world ranking.

&nbsp;

&nbsp;

VIT University

Design of an artificial high flexion knee

2007 IEEE/NIH Life Science Systems and Applications Workshop

Journal of Medical Marketing

Techno-economical analysis of the potential rise of demand for the artificial high flexion knee in the Indian orthopaedics market

Total knee arthroplasty (TKA) has been the end-time surgical procedure for pain relief and movement restoration in cases of severe arthritis. The knee implant design plays a vital role in deciding the activity levels of a patient after total knee replacement (TKR). In about 90% of younger patients undergoing the knee replacement surgeries, the restriction is not from the subject but from the implant design. This paper discusses parameters affecting the activity levels after TKR. It also briefs the design aspects of a novel knee design that allows the normal high flexion activity even after TKR. The application of finite element modeling in medical applications has been evolving as the field of high importance especially in the development of medical devices. The TKA has been in existence for over six decades till now. The generic artificial knee implants used in the TKA have the restriction in its range of motion of about 90°. A new design allowing flexion extension range of over 120° was designed with a view to facilitate partial squatting and the same is used for the analysis purpose. The loading conditions of 10 times the body weight are considered. The finite element analyses of the designs were carried out based on standard biomaterial used in orthopedic implants. In this paper, we have discussed the results of analyses of an artificial knee with titanium (Ti) alloy. The results of the analyses were used in identifying areas of extreme stresses within the design and the spot prone for higher deformation. Based on these results, slight modification on the designs was carried out. The results are also verified whether the body is within the linear deformation levels. As the results obtained were very satisfactory, the models have been recommended for prototyping.

Biomedical Engineering: Applications, Basis and Communications

KINEMATIC ANALYSIS AND 3D FINITE ELEMENT ANALYSIS OF A MOBILE-BEARING ARTIFICIAL HIGH FLEXION KNEE

The application of finite element modeling in medical applications has been evolving as the field of high importance especially in the development of medical. The generic artificial knee implants used in the total knee arthroplasty have the restriction in its range of motion with around 90 degrees. A new design allowing flexion extension range of over 120 degrees has been designed with a view to facilitate partial squatting and the same is used for the analysis purpose. The loading conditions of 10 times the body weight are considered. Finite element analyses of this design have been carried out based on standard biomaterial used in orthopaedic implants. In this paper we discuss the results of analyses of an artificial knee with stainless steel alloy. The results of the analyses were used in identifying areas of extreme stresses within the design and the spot prone for higher deformation. Based on these results slight modification on the designs was carried out. The results are also verified whether the body is within the linear deformation levels. As the results obtained were very satisfactory the models have been recommended for prototyping. It is verified from the results that the new models respond positive till a load of 300 kg and then they enter into the maximum yield stress levels. However, in reality, the loading on an artificial knee is less than 300 kg. So the results are inferred positive and the models were sent for prototyping.

Biophysical Reviews and Letters

STRUCTURAL RESPONSES OF A NOVEL HIGH FLEXION KNEE (SS316–UHMWPE) USED IN TOTAL KNEE ARTHROPLASTY USING FINITE ELEMENT ANALYSIS

IFMBE Proceedings 13th International Conference on Biomedical Engineering

Artificial High — Flexion Knee Customized for Eastern Lifestyle

Journal	Data powered by Typeset2007 IEEE/NIH Life Science Systems and Applications Workshop
Publisher	Data powered by TypesetIEEE
Open Access	0