The metallurgical and mechanical properties of electron beam welded Ni based superalloy Inconel 625 and UNS S32205 duplex stainless steel plates have been investigated in the present study. Interface microstructure studies divulged the absence of any grain coarsening effects or the formation of any secondary phases at the heat affected zone (HAZ) of the electron beam (EB) weldments. Tensile studies showed that the fracture occurred at the weld zone in all the trials and the average weld strength was reported to be 850. MPa. Segregation of Mo rich phases was witnessed at the inter-dendritic arms of the fusion zone. The study recommended the use of EB welding for joining these dissimilar metals by providing detailed structure - property relationships. © 2014 Elsevier Ltd.

Devendranath Ramkumar K

Department of Manufacturing Engineering

School of Mechanical Engineering

Vellore Campus

Sridhar R

Computer Science

School of Computer Science and Engineering

Chennai Campus

Arivazhagan N

Periwal S

Oza S

Saxena V

Hidad P

Vellore Institute of Technology (VIT) is a private university located in&nbsp;Tamil Nadu, India. Founded in 1984, as Vellore Engineering College, the institution offers 20 undergraduate, 34 postgraduate, four integrated and four research programs. It has campuses in Vellore, Amravati, Bhopal and Chennai.

VIT is one of the top ranked private universities in India according to NIRF, THE and QS Rankings.&nbsp;Govt. of India has recognized&nbsp;VIT, Vellore as an&nbsp;Institution of Eminence. This has allowed VIT to take independent quality initiatives and move up in world ranking.

&nbsp;

&nbsp;

VIT University

Materials & Design

The present study addresses the effect of fillers on the microstructure and tensile strength of dissimilar joints of Inconel 625 and UNS S32205 by pulsed current gas tungsten arc welding (PCGTAW) employing ERNiCrMo-10 and ERNiCrMo-14 fillers. This study attested that tensile failure occurred in the fusion zone of the dissimilar joints for both the cases in the as-welded un-peened condition. Double shot laser shock peening (DLSP) was performed on the fusion zone of these PCGTA welds on the cap and root regions of the weldments. It was assimilated that after DLSP on the cap and root regions of the weldments, the yield and tensile strength of the welded joints employing these fillers were improved considerably. Residual stress analysis were carried out on the dissimilar coupons using X-ray Diffraction analysis. The results demonstrated that after subjecting to double sided DLSP, the fusion zones were subjected to compressive residual stresses. The present study articulated that shot peening using low energy laser beam resulted in better tensile strength. © 2016 Elsevier B.V.

Materials Science and Engineering: A

Influence of laser peening on the tensile strength and impact toughness of dissimilar welds of Inconel 625 and UNS S32205

The dissimilar combinations of Inconel 625 and duplex stainless steel SAF 2205 obtained from manual GTA welding process employing ER2209 and ERNiCrMo-3 filler metals have been investigated. Formation of secondary phases at the HAZ of Inconel 625 and grain coarsening at the HAZ of SAF 2205 were witnessed while using these filler wires. The average hardness of ER2209 weldments was found to be greater than ERNiCrMo-3 weld. Tensile fracture was observed at the weld zones for both the fillers. Impact test trials showed brittle mode of fracture on employing ER2209 filler and mixed (ductile-brittle) mode of fracture while using ERNiCrMo-3 filler. Further optical microscopy and SEM/EDS analysis were carried out across the weldments to investigate the structure-property relationships. © The Chinese Society for Metals and Springer-Verlag Berlin Heidelberg 2014.

Fulltext

Acta Metallurgica Sinica (English Letters)

Characterization of Microstructure, Strength, and Toughness of Dissimilar Weldments of Inconel 625 and Duplex Stainless Steel SAF 2205

Journal of Surgery

http://www.avensonline.org/fulltextarticles/JSUR-2332-4139-S1-0001.html

Vacuum

Microstructure and hardness studies of electron beam welded Inconel 625 and stainless steel 304L

Microstructural evolution and mechanical properties of high strength 3–9% Ni-steel alloys weld metals produced by electron beam welding

The International Journal of Advanced Manufacturing Technology

Microstructural studies and impact toughness of dissimilar weldments between AISI 316 L and AH36 steels by FCAW

Investigations on the structure – Property relationships of electron beam welded Inconel 625 and UNS 32205

Journal	Data powered by TypesetMaterials & Design
Publisher	Data powered by TypesetElsevier BV
ISSN	0261-3069
Open Access	No