The solar flat plate collector operating under different convective modes has low efficiency for energy conversion. The energy absorbed by the working fluid in the collector system and its heat transfer characteristics vary with solar insolation and mass flow rate. The performance of the system is improved by reducing the losses from the collector. Various passive methods have been devised to aid energy absorption by the working fluid. Also, working fluids are modified using nanoparticles to improve the thermal properties of the fluid. In the present work, simulation and experimental studies are undertaken for pipe flow at constant heat flux boundary condition in the mixed convection mode. The working fluid at low Reynolds number in the mixed laminar flow range is undertaken with water in thermosyphon mode for different inclination angles of the tube. Local and average coefficients are determined experimentally and compared with theoretical values for water-based Al2O3 nanofluids. The results show an enhancement in heat transfer in the experimental range with Rayleigh number at higher inclinations of the collector tube for water and nanofluids. © 2015, Springer-Verlag Berlin Heidelberg.

Raja Sekhar Y

Department of Thermal and Energy Engineering

School of Mechanical Engineering

Vellore Campus

Sharma K.V

Kamal S.

Vellore Institute of Technology (VIT) is a private university located in&nbsp;Tamil Nadu, India. Founded in 1984, as Vellore Engineering College, the institution offers 20 undergraduate, 34 postgraduate, four integrated and four research programs. It has campuses in Vellore, Amravati, Bhopal and Chennai.

VIT is one of the top ranked private universities in India according to NIRF, THE and QS Rankings.&nbsp;Govt. of India has recognized&nbsp;VIT, Vellore as an&nbsp;Institution of Eminence. This has allowed VIT to take independent quality initiatives and move up in world ranking.

&nbsp;

&nbsp;

VIT University

Environmental Science and Pollution Research

In this study, the exergetic performance of a flat plate solar collector (FPSC) setup with ZnO-based ethylene glycol (EG)/water nanofluid as a working fluid has been evaluated against that of EG/water. As a passive means to augment the rate of heat transfer, internally grooved tubes of two different pitches (e = 0.43 and e = 0.44) have been examined and compared against the performance of plain tube. The mass flow rate was fixed at 0.015 kg/s and the volume fraction of ZnO nanoparticles is ф = 0.02% v/v. The results indicate an enhancement in exergy efficiency of 44.61% when using the grooved tube (e = 0.44) against plain tube without the nanofluid and 39.17% when nanofluid is used. Using the nanofluid enhanced the exergy efficiency of the FPSC by a maximum of 73.81%. Maximum exergy efficiency obtained was 5.95% for grooved tube (e = 0.44) with nanofluid as working fluid and is in good agreement with previous literature. Exergy destruction/irreversibility due to temperature differences and heat flow within the system has been reported. Sun-collector temperature difference accounts for nearly 86–94% of the irreversibility. The results for thermal efficiency of this experimental setup have been published and summarized in this study for reference.

Journal of Solar Energy Engineering

Exergy Analysis of a Flat Plate Solar Collector With Grooved Absorber Tube Configuration Using Aqueous ZnO–Ethylene Glycol

International Journal of Thermal Sciences

Natural convection in nanofluids: Are the thermophoresis and Brownian motion effects significant in nanofluid heat transfer enhancement?

Experimental study of mixed convection with water–Al2O3 nanofluid in inclined tube with uniform wall heat flux

Current Applied Physics

Convective heat transfer characteristics of nanofluids under laminar and turbulent flow conditions

The effect of cylinder inclination on thermal buoyancy induced flows and internal natural convective heat transfer is explored using CFD simulations. The cylinder's top and bottom surfaces were maintained at different temperatures while the curved surface was adiabatic. The aspect ratio (length/diameter) of the cylinder was unity and the Prandtl number of the fluid was fixed at 0.71. The Rayleigh number of the confined fluid was varied from 103 to 3.1 × 104 by changing the specified end wall temperatures. The critical Rayleigh number was estimated to be 3800 for the vertical cylinder. Relaxing the convergence criterion caused false hysteresis in the converged results for the vertical cylinder. Typical natural convective fluid flow and temperature patterns obtained under laminar flow conditions are illustrated for various inclinations ranging from 0° to 180°. Flow visualization studies revealed complex three-dimensional patterns. Different thermal-hydrodynamic regimes were identified and were classified in terms of Rayleigh number and angle of inclination. Empirical correlations for the Nusselt number and maximum velocities in the domain as a function of the inclination angle and Rayleigh number are developed. © 2008 Elsevier Ltd. All rights reserved.

International Journal of Heat and Mass Transfer

Numerical studies on laminar natural convection inside inclined cylinders of unity aspect ratio

Flow and convective heat transfer characteristics of water-based Al2O3 nanofluids in fully developed laminar flow regime

Nanofluid heat transfer under mixed convection flow in a tube for solar thermal energy applications

Journal	Data powered by TypesetEnvironmental Science and Pollution Research
Publisher	Data powered by TypesetSpringer Science and Business Media LLC
ISSN	0944-1344
Open Access	0